			NetSentinel NT Service
	      Copyright (c) 1991-2000 Rainbow Technologies
			 All Rights Reserved


 Thank you for choosing NetSentinel from Rainbow Technologies!  This
 version of the NetSentinel security server is implemented as a Windows
 NT service which allows the server application to be automatically
 started whenever the Windows NT operating system is running.  It
 supports NetBIOS, NetBEUI, NWLink (Microsoft IPX/SPX compatible
 protocol) and TCP/IP protocols.

 This file provides the following information about the NetSentinel 
 NT Service:
      1.0  Installation/Operating Instructions
	   1.1 To install the NetSentinel NT service.
	   1.2 To specify command line options.
	   1.3 To start the NetSentinel NT service
	   1.4 To uninstall the NetSentinel NT service
	   1.5 To display the software version
      2.0  Service Event Logging
      3.0  Operating Environment

--------------------------------
IMPORTANT! IMPORTANT! IMPORTANT!
--------------------------------

 You will need Sentinel System Drivers Version 5.18 or later to run the
 NetSentinel NT service.  If an earlier version of the driver is in 
 use, an event log will be generated and the service will terminate.

---------------------------------------
1.0 INSTALLATION/OPERATION INSTRUCTIONS
---------------------------------------
 
 Before running NetSentinel NT service, the service must be installed
 into the system.  

1.1 To install the NetSentinel NT service:
------------------------------------------

   1. NSSRVICE.EXE must be copied to the Windows NT 
      %SystemRoot%\System32 directory to ensure the accessibility of
      the file during the service start up.

   2. To install the service, run the NSSRVICE.EXE executable with 
      "/I" option, i.e. NSSRVICE /I.

   3. After installation, a registry entry for NetSentinel service is
      created under 
	  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services

   4. By default, the service is setup to run automatically the next
      time you reboot your Windows NT system.  No user logon is 
      required, unless desired.

1.2 To specify command line options:
------------------------------------

 In addition, the following command line options can be used to specify
 options for the server application:

	/DN:string - Changes the server's department name.
	/H:num     - Sets the maximum number of licenses that can be in
		     use at any one time on this server.
	/MS:num    - Sets the maximum number of servers allowed.
	/N:string  - Sets the name displayed by the monitor for this
		     server.
	/ST        - Enables strict timeout enforcement.
	/SN:num    - Sets the maximum NetBIOS sessions.
	/SW:num    - Sets the maximum NWLINK  sessions.
	/SI:num    - Sets the maximum TCP/IP  sessions.
	/SL:num    - Sets the maximum number of sub-licenses.
	/BI:num    - Overrides TCP/IP default broadcast mask
		     (255.255.255.255).
	/RI:num    - Sets number of times to retry finding the 
		     specified Rainbow TCP/IP Server.
	/TI:num    - Timeout value used when attempting to locate
		     other Rainbow TCP/IP Servers.
	/W:string  - Specifies handle delete password.        

	/?         - Displays help screen.

 Specified options, if any, take effect the next time the service is
 started.


1.3 To start the NetSentinel NT service:
----------------------------------------

 After the service has been properly installed, you may reboot your
 system to start the NetSentinel NT service automatically at system
 boot time.  You can also use either the NET command or the Service
 applet in the Control Panel to manually control the service.

 To use the NET command method, type the following commands at the
 command prompt:

   . NET START NETSENTINEL     - Starts the service.

   . NET STOP NETSENTINEL      - Stops the service.

 To use the Service applet in Control Panel:

   1. From the Control Panel, select Services.  The Services dialog
      box appears.

   2. Select NetSentinel service.

   3. Press the Start or Stop button to start or stop the NetSentinel
      NT service.


1.4 To uninstall the NetSentinel NT service:
--------------------------------------------

   1. Log onto the workstation if you haven't already done so.

   2. Stop the NetSentinel NT service using either the NET command
      method or the Services applet as described earlier.

   3. Run the NSSRVICE.EXE executable with "/U" option, i.e.
      NSSRVICE /U, to uninstall the service.

   4. The registry entry for NetSentinel service under
      HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services will be
      removed after uninstall.

1.5 To display the software version:
------------------------------------

 . Run the NSSRVICE.EXE executable with "/V" option, i.e. NSSRVICE /V.

---------------------
SERVICE EVENT LOGGING
---------------------

 Status information pertaining to this service is reported to the
 application log.  Upon successful startup of the service, information
 such as server version, protocol stacks, and available keys is logged
 as two separate events in the application log.  Please access Event
 Viewer in the Administrator Tools group to view this information.

---------------------
OPERATING ENVIRONMENT
---------------------

 Support Windows NT Version 3.5, 3.51, and 4.0.



 
